Vision Fitness U70 Wartungshandbuch

Vision Fitness U70-02 (CB68C) Service Manual

10CHAPTER 3: ENGINEERING MODE 3.1 Using Engineering Mode 1. Press & Hold both UP and DOWN RESISTANCE keys at the same time for 3-5 second to ente

11CHAPTER 3: ENGINEERING MODE 3.1 Using Engineering Mode – Continued CUSTOMSETTING DEFAULT MINIMUM MAXIMUM DESCRIPTION MAX TIME 99 min 5 min 99

12CHAPTER 4: TROUBLESHOOTING 4.1 Console Error Codes Error Messages on the Console Code Class Description Solution 0x0441 B When UCB implements a

13CHAPTER 4: TROUBLESHOOTING 4.2 Troubleshooting – No Display on the Console or the Display is Dim NO DISPLAY ON THE CONSOLE OR THE DISPLAY IS DIM

14CHAPTER 4: TROUBLESHOOTING 4.3 Troubleshooting – No RPM is Displayed During the Exercise NO RPM IS DISPLAYED DURING THE EXERCI

15CHAPTER 4: TROUBLESHOOTING 4.4 Troubleshooting – All or Some of the Function Keys Do Not Respond ALL OR SOME OF THE FUNCTION KEYS DO NOT RESPOND

16CHAPTER 4: TROUBLESHOOTING 4.5 Troubleshooting – High or No Resistance HIGH OR NO RESISTANCE POSSIBLE CAUSES: 1) The console is damaged or the

17CHAPTER 4: TROUBLESHOOTING 4.6 Troubleshooting – Pedals Slipping PEDALS SLIPPING POSSIBLE CAUSES: 1) The belt tension is not high enough. 2) T

18CHAPTER 4: TROUBLESHOOTING 4.8 Troubleshooting – Heart Rate Function Does Not Work or is Reading Incorrectly HEART RATE FUNCTION DOES NOT WORK OR

19CHAPTER 5: PART REPLACEMENT GUIDE 5.1 Console Replacement 1) Remove the 4 screws holding the console to the frame (Figure A). FIGURE A 2) Discon

2TABLE OF CONTENTS CHAPTER 1: MAINTENANCE PROCEDURE 1.1 Preventive Maintenance Schedule…………………………………………………………..4 1.2 Cleaning the Grooves……………

20CHAPTER 5: PART REPLACEMENT GUIDE 5.2 Heart Rate Handlebar Replacement 1) Remove the 4 screws holding the heart rate handlebar to the console mast

21CHAPTER 5: PART REPLACEMENT GUIDE 5.3 Heart Rate Grips Replacement 1) Remove the 2 screws holding the HR grip together (Figure A). 2) Once the 3

22CHAPTER 5: PART REPLACEMENT GUIDE 5.4 Cup Holder Replacement 1) Remove the 2 screws holding the cup holder to the console mast (Figure A). FIGUR

23CHAPTER 5: PART REPLACEMENT GUIDE 5.5 Console Mast Replacement 1) Remove the console as outlined in Section 5.1. 2) Remove the HR handlebars as

24 CHAPTER 5: PART REPLACEMENT GUIDE 5.6 Seat Pad Replacement 1) Remove the 3 screws holding the seat pad to the seat post (Figure A). FIGURE A 2)

25CHAPTER 5: PART REPLACEMENT GUIDE 5.7 Seat Post Replacement 1) Remove the seat adjustment pin (Figure A). 2) Pull the seat post upward until the

26CHAPTER 5: PART REPLACEMENT GUIDE 5.8 Seat Post Insert Replacement 1) Remove the seat adjustment pin (Figure A). 2) Pull the seat post upward un

27CHAPTER 5: PART REPLACEMENT GUIDE 5.9 Pedal Replacement 1) Use a 15 mm pedal wrench to remove the pedal from the crank (Figure A). NOTE: For the ri

28CHAPTER 5: PART REPLACEMENT GUIDE 5.10 Crank Removal NOTE: A special tool is needed to correctly replace a crank. Order part: # 022696-00 from Visi

29CHAPTER 5: PART REPLACEMENT GUIDE 5.11 Shrouds Removal 1) Remove the crank as outlined in Section 5.10. 2) Remove the seat adjustment pin (Figure

3 CHAPTER 5: PART REPLACEMENT GUIDE 5.14 Idler Set Replacement...

30CHAPTER 5: PART REPLACEMENT GUIDE 5.12 Lower Control Board Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) Disconnect the 3 wi

31CHAPTER 5: PART REPLACEMENT GUIDE 5.13 Drive Belt Replacement 1) Remove the right side shroud as outlined in Section 5.11. 2) Pull up on the ten

32CHAPTER 5: PART REPLACEMENT GUIDE 5.14 Idler Set Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) The Idler set is attached to

33CHAPTER 5: PART REPLACEMENT GUIDE 5.15 Generator Belt Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) Remove the cable ties on

34CHAPTER 5: PART REPLACEMENT GUIDE 5.15 Generator Belt Replacement – Continued 6) Remove the generator belt (Figure E). 7) Pull the generator out o

35CHAPTER 5: PART REPLACEMENT GUIDE 5.16 Generator Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) Remove the cable ties on the

36CHAPTER 5: PART REPLACEMENT GUIDE 5.16 Generator Replacement – Continued 6) Remove the generator belt (Figure E). 7) Pull the generator out of the

37CHAPTER 5: PART REPLACEMENT GUIDE 5.17 Pulley Axle (Secondary) Set Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) Remove the d

38CHAPTER 5: PART REPLACEMENT GUIDE 5.17 Pulley Axle (Secondary) Set Replacement – Continued 7) Install a screw into the secondary axle and turn the

39CHAPTER 5: PART REPLACEMENT GUIDE 5.18 Drive Axle Set Replacement 1) Remove the shrouds as outlined in Section 5.11. 2) Pull up on the tension as

4CHAPTER 1: MAINTENANCE PROCEDURE 1.1 Preventive Maintenance Schedule PREVENTIVE MAINTENANCE SCHEDULE Item Daily Weekly Monthly Quarterly Bian

40CHAPTER 5: PART REPLACEMENT GUIDE 5.18 Drive Axle Set Replacement – Continued 5) Install two nuts into the pulley axle and turn the nuts until the

41CHAPTER 5: PART REPLACEMENT GUIDE 5.18 Drive Axle Set Replacement – Continued 7) Use a mallet with a punch to hit the remained bearing until it is

42CHAPTER 5: PART REPLACEMENT GUIDE 5.19 Rear Stabilizer Replacement 1) Lean the bike to one side and remove the 4 screws holding the rear stabilize

43CHAPTER 5: PART REPLACEMENT GUIDE 5.20 Testing the Bike ONCE THE UNIT OR REPLACEMENT PART IS FULLY INSTALLED AND ASSEMBLED AND PROPERLY PLACED ON

44CHAPTER 6: SOFTWARE UPGRADE PROCEDURE 6.1 Software Upgrade Instructions A. Service Tools & Accessories: 1. MSP-FET430 Gang Programmer 2. Par

45CHAPTER 6: SOFTWARE UPGRADE PROCEDURE 6.1 Software Upgrade Instructions – Continued B. VISION U70 BIKE SOFTWARE UPGRADE PROCEDURE 1. Connect the

46CHAPTER 6: SOFTWARE UPGRADE PROCEDURE 6.1 Software Upgrade Instructions – Continued 3.3 Select the required device using the Device Type menu.

47CHAPTER 6: SOFTWARE UPGRADE PROCEDURE 6.1 Software Upgrade Instructions – Continued 4. After the first console is installed, you can remove the RS

5CHAPTER 1: MAINTENANCE PROCEDURE 1.2 Cleaning the Grooves If there is any dust in the grooves of the Poly-V belts and pulleys, noises will be genera

6CHAPTER 2: WIRING DIAGRAM INSTRUCTION\ 2.1 Electrical Installation

7CHAPTER 2: WIRING DIAGRAM INSTRUCTION\ 2.2 Electrical Diagram

8CHAPTER 2: WIRING DIAGRAM INSTRUCTION\ 2.3 Wiring Diagram P01- CONSOLE WIRE 2.4 Lower Control Board Diagram J2

9CHAPTER 2: WIRING DIAGRAM INSTRUCTION\ 2.5 Console Wiring Diagram Port Function JQK Quick key cable for S70 JQK1 Quick key cable